Take graduated containers and measure 2 parts of part A Resin to 1 part of part B Hardener.Wear hand and eye protection as a precaution when working with this product.Make sure you are in a dust free and hair free work zone. Cover and protect all surfaces on and around your work area with plastic sheeting before you begin.Make sure your molds and graduated cups are fully dried from the water before use and there is no moisture left in your mold. It should give you a pretty close estimate of how many ounces are needed. Then pour the water into a graduated container to see how many ounces are needed to fill the mold. A great trick to figure out how much resin you will need for you mold is to pour water into your mold to the fill point.For medium to large molds recommended temperature is 65 degrees to cool and slow the exothermic reaction during the curing process. For small molds, recommended temperature is 70-75 degrees. Recommended working temperature differs based on the volume of the pour. Make sure your resin is stored at room temperature around 70 degrees.Naked Fusion Resin Instructions for Casting Medium to Large Molds It is the time window to be creative with your project. Working time is the time you have to work with your resin after it has been poured out of your mixing container before it gels and starts to harden on your project. If you are working with smaller amounts of resin you will have more time with your pot life. If you are working on a larger project and you are mixing 1 gallon to 3 gallons at a time in one mixing container, the mixed resin and hardener will generate heat and will need to be poured into your project right after mixing it. For example if you need to mix 60 oz total, you can mix 20 oz in each container which will buy you more time before you have to pour it out. To extend pot life, you can mix your hardener and resin into 2 or 3 smaller containers. Once it is poured into a 1 ½ to 2 inch depth there is still open time to work with it. Larger volumes of mixed resin have an exothermic reaction and generate heat much faster. If you are working with over a gallon of resin, we recommend pouring it out into your project right away. For example, a 9 oz cup of mixed resin will have a longer pot life than a gallon or 3 gallons of mixed resin. The volume of resin you are mixing has an effect on the pot life. With most resins, pot life is shorter than working time. Faulty product, automatic replacement on return of goods to the company.Pot life is the time that your mixed resin and hardener sits in your mixing container before it is poured into your project.In the UK, any problem reported to us on delivery will be dealt with in the following manner: The company has an ongoing belief that good customers expect and deserve a top class service. Penetrating Epoxy Sealer works great for sealing the wood to reduce the risk of air bubbles and foam appearing while curing.Įpoxy.Ltd will deliver any paid for goods in the quickest possible way, usual delivery is 2/3 days however were we are sending goods overseas (this means across any water) this period may be extended up to two weeks or longer at the company’s discretion. We recommend sealing any wood or porous surfaces prior to using Deep Pour Epoxy. Higher temperatures will accelerate the epoxy curing process, resulting in discolouration, shrinkage and/or cracking. Temperature Range: 65-80☏.ĭO NOT pour epoxy in conditions over 80 deg F. For best results, let the first pour cure, lightly sand the surface and wipe clean before applying the next layer of epoxy. ALWAYS allow the previous pour to cool past the peak exotherm before step pouring, adding additional material over the top. If you have any questions or concerns about the process please give us a call or send us an email at Maximum Pour Depth: We recommend pouring to a maximum thickness of 1-2 inches.įor larger voids and thicker pours, we recommend step pouring 1 in. Pouring too much epoxy into a large area may result in shrinking, yellowing or cracking. Please take into consideration the volume of epoxy you pour into a void. PLEASE NOTE: This is an advanced epoxy resin system. It cures within 24-36 hours at 70 degrees F creating a clear, glass-like finish that resists scratching and yellowing with an extended gel time to minimize exotherm and improved air release. MAS Deep Pour Epoxy Casting Resin System is a 100% solid, two-component, three to one by volume mix ratio formulated for deep pour casting, encapsulating and moulding applications.
0 Comments
Leave a Reply. |